1.02 For Material less than 0.250" thick in T3, T4, T6, T76 and T81 Tempers purchased as "MRS (Minimum Residual Stress) Quality" shall meet the requirement of BATS 2505
1.03 Material 1/2 inch thick and greater shall be 100 per cent ultrasonically inspected per ASTM B594 to the Discontinuity Class Requirement of the applicable material specification and/or applicable engineering drawing. For shapes, the thickness of any element of the shapes shall be deemed to be the smallest dimension of that element.
1.05 Ultrasonic inspect by an approved source, only when specifically required by the engineering drawing.
1.07 Fuel shall contain anti-icing additive and antistatic additive meeting electrical conductivity reading per material Specification requirements
1.08 Primer shall be specified to be bought in bulk or aerosol form. Unless otherwise specified colour shall be yellow.
1.10 Materials shall be purchased etched one side. The elapsed time since the etching shall not exceed 3 months.
1.11 Procurement shall specify dimensions such as OD or ID for tube form, and diameter or distance between parallel sides for rods and shapes. Waive radiographic inspection.
1.12 Materials 0.025 inches or greater in thickness and > 36 inches in width shall be flat within 3%. Materials less than 0.025 inches thick and over 36 inches in width shall be flat within 4% of the distance between contact points of a straight edge laid in any direction upon the material.
1.13 For sheet, thickness 0.032 inches and 60 inches width thickness tolerance shall be ± 0.004 inch.
1.14 Every shipment shall contain at least one part having a 6 inch prolongation for testing purposes at Bombardier Aerospace.
1.15 When procuring compounds from supplier(s) the primer for these compounds should be procured from the same supplier(s).
1.16 If additional requirements per MIL-C-27500 are necessary they should be noted on the Purchase Order.
1.17 Class 2 salt shall be supplied with 1% sodium dichromate added.
1.19 For specification MIL-A-18455, argon gas purity shall be 99.996 percent minimum argon by volume, dew point shall be -76° F or lower and the oxygen content shall be 5.0 ppm maximum by volume.
1.21 Premixed and frozen adhesive must have 3 weight percent TS 720 CAB-O-SIL.
1.22 Each order must specify width of roll and that a liner is required.
1.23 Minimum continuous cable length shall be 30 ft.
1.24 Minimum continuous cable length shall be 40 ft.
1.25 Conductors shall be insulated with Refrasil and overbraided with stainless steel braid.
1.26 Procurement must specify style 120 class cloth, width, resin content 46 ± 3%, good tack and flow of 14 to 46%.
1.27 Procurement must specify fabric width, style of fabric, resin content 38 ± 2%, flow at 50 psi and 275° F = 14 ± 6%.
1.28 Procurement must specify the vendor's designation noted above, the tape with gel, flow and resin content requirements.
1.29 Procurement must specify width of fabric and resin content by weight (55 ± 5% solids).
1.30 Procurement must specify fabric width, resin content 40 ± 3%, flow 20-27%.
1.31 Procurement must specify width of film and gel time requirement of 15 minutes at 350°F.
1.32 Tolerances for sheet are all tempers, thickness up to 3.0 inches.
1.33 Tolerances for sheet are all tempers, thicknesses 0.250 to 4.0 inches.
1.34 Tolerances for sheet T351 temper only, thicknesses 0.250 to 4.0 inches
1.35 Tolerances for sheet T651 temper only, 0.250 to 4.0 inches.
1.36 Procurement must specify colour by reference to AMS-STD-595 number, BAC colour standard number, or other commercial colour standard number specified in the engineering documentation.
1.37 Specify colours to match BMS 10-11 colour standards to yellow (BAC 377) and green (BAC 452).
1.38 Material 1/2 inch thick and greater shall be 100 per cent ultrasonically inspected per ASTM B594 Class A. For shapes, the thickness of any element of the shapes shall be deemed to be the smallest dimension of that element.
1.39 Type I (Round) tube in T6 temper with outside diameter less than 1.5 inches must have a minimum of 15% elongation.
1.40 Procurement must specify: Gel Time 9 ± 2 minutes tested at 250F, Flow 9 to 22% tested at 250F and 50 psi, Resin Content 42 ± 3% wt.
1.41 In addition to the type and finish combinations listed in MIL-T-43435, Western Filaments Inc. offers Type V in Finish E. This is approved and listed in BAPS 145-003.
1.42 For each cable symbol the approved sources are the same as those for corresponding wires.
1.43 Wire to be used on Minneapolis - Honeywell fuel quantity system only.
1.44 Specify construction and for Type II outside diameter of jacket.
1.45 For permitted material thickness or size substitutions refer to BAERD GEN-003.
1.46 Purchase in degreased condition.
1.47 Procurement must specify these 3 conditions: (1) Thickness 30 ± 0.15 mm or 60 ± 0.20 mm (2) Density 64 ± 6.4 kg/m³ and (3) Nominal Aramid Paper thickness 0.076 mm
1.48 Specify if ribbon direction is in length or width.
1.49 Specify form and hardness.
1.50 Shelf life based on cure date.
1.52 General shelf life and special (reduced) shelf life for supply as spares are defined in I.G.C. 04.84.100
1.54 Etched teflon sheets shall be rolled up with the etched side toward the center (inside)
1.55 Specify colour. Unless otherwise noted on drawings, order BAC 707 Gloss Grey.
1.56 The material specification and class/alloy type shall be marked on each rod or electrode by the manufacturer.
1.58 Base and hardener/catalyst shall be maintained at all time as a certified kit in the proportions indicated in the Material Description.
1.59 All components shall be purchased at the same time in the proportions indicated in the Material Description.
1.60 Bottles shall be labelled as follows: BAMS 565-001 GR A; Batch No. (from paint supplier).
1.61 Bottles shall be labelled as follows: BAMS 565-002 GR A; Batch No. (from paint supplier).
1.62 No BAMPE purchase conditions apply.
1.63 Purchase material to Revision A of specifications.
1.64 Bottles shall be labelled as follows: BAMS 565-010; MRV No (from Bombardier Aerospace); Batch No (from paint supplier).
1.65 CA106 accelerator may be ordered as part of a kit.
1.66 Purchase material to revision C of specification
1.67 Cans shall be identified with the BAMS 565-007 & ASN-B-70720 SP designations.
1.68 100 percent ultrasonic inspect per BAC 5439 Class A (Class B optional)
2.01 If material is purchased directly from the manufacturer, a Certificate of Compliance and a Test Report from the manufacturer is required for each lot or batch of material. If the Certificate of Compliance states the test report is available electronically, a hard copy need not be submitted with shipment.
2.02 If material is purchased from a vendor who is not the manufacturer, then a vendor's Certificate of Compliance is required, in addition to the material manufacturer's Certificate of Compliance and Test Report, for each lot or batch of material. If the Certificate of Compliance states the test report is available electronically, a hard copy need not be submitted with shipment.
2.03 If material is purchased directly from the manufacturer, a Certificate of Compliance from the manufacturer is required for the lot or batch numbers involved.
2.04 If material is purchased from a vendor who is not the manufacturer, then a vendor's Certificate of Compliance is required. It shall include traceability to the manufacturer of each original lot or batch.
2.05 A Certificate of Compliance from the manufacturer of the sheeting is required for each lot of sheet. In addition, a Certificate of Compliance from the resin manufacturer is required for each lot of resin comprising each lot of sheet supplied by the sheet manufacturer.
2.06 If material is purchased from a vendor who is not the manufacturer, then a vendor's Certificate of Compliance is required, in addition to the manufacturer's Certificate of Compliance.
2.07 A Certificate of Compliance to FAR Part 25, Paragraph 25.853, test methods as per Appendix F.
2.08 A Certificate of Compliance to FAR Part 25, Paragraph 25.855, test methods as per Appendix F.
2.09 The supplier shall provide a Certificate of Conformance stating that the material meets all requirements of MIL-T-81533 and that the minimum total acid acceptance value (as equivalent NaOH, weight%) is 0.12%, when tested as per ASTM D2942.
2.10 Must conform to qualifications of BAPS 212-004.
2.11 Specify on the container that the product shall not be frozen.
2.12 Shield symbol type S and outer jacket material 22 as designated in MIL-C-27500. Conductors to be laid parallel not twisted.
2.13 Procurement shall be from European Sources only.
2.14 Vendor to supply release note with data indicating conformance to specification.
2.16 Applies to diameters up to 75mm inclusive in a heat treat level of 1230 MPa to 1380 MPa, and for diameters of 80mm and over in an annealed condition.
2.17 Applies to diameters up to 100mm inclusive in a heat treat level of 1080 MPa to 1270 MPa, and for diameters of 100mm and over in annealed condition. State condition in purchase order.
2.18 Purchase order shall request the following tests: (a) Chemical Composition (b) Mechanical Properties (c) Impact Properties (d) Magnetic Inspection (e) Ultrasonic Inspection (f) Microstructure (g) Inclusion (h) Residual Austenite
2.19 Material shall be procured in final condition (1200 MPa Tensile Strength) in addition, for each billet, an extra 8 inch long of material shall be bought for testing purposes.
2.20 Material may be procured in conditions F, T6, T6511, T73, T73511. State temper in purchase order.
2.21 Material must conform to IGC 04.32.105
2.22 Material must conform to ASN-B-74506
2.23 Material must conform to NF.L.17131
2.24 Material must conform to NF.L.17150
2.25 Material must conform to NF.L.17153
2.26 Material must conform to NF.L.17121
2.27 Material must conform to NF.L.17141
2.28 Material must conform to NF.L.17142
2.29 Material must conform to IGC 04.36.148
2.30 Material must conform to IGC 04.36.139
2.31 Material must conform to IGC 04.36.142
2.32 Material must conform to IGC 04.36.141
2.33 Material must conform to ASN-4014-3000
2.34 Material must conform to ASN-B-73501
2.35 Material must conform to ASN-B-73411
2.36 Material must conform to ASN-B-73520
2.37 Material must conform to IGC 04.38.168
2.38 Material must conform to IGC 04.31.134
2.39 Material must conform to IGC 03.33.112
2.40 Material must conform to IGC 04.32.223
2.41 Material must conform to IGC 04.34.114
2.42 Material must conform to NSA 384.510
2.43 Material must conform to IGC 04.31.124
2.44 Material must conform to IGC 04.31.130
2.45 Material must conform to IGC 04.31.200
2.46 Material must conform to IGC 04.32.264
2.47 Material must conform to IGC 04.32.113
2.48 Material must conform to ASN-A-4239
2.50 Grade 3, Class 1 MIL-C-16173E may be purchased from CRC Industries, Inc. under the Ultra Lite Lub generic name.
2.54 Material must conform to BAMS 516-007
2.55 Cans shall be identified with the BAMS 565-007 and ASN-B-70720 SP designations
2.56 Material must conform to ASN-A-4040
2.57 Material must conform to IGC 04.33.114
2.58 Forged billet/block must meet dimensional requirements of drawing. If drawing does not specify dimensional requirements, they should be requested from Bombardier Aerospace Engineering.
3.01 Ship at temperature controlled from -40°F and below. Each box of cartridges must contain a temperature recorder or must have evidence of dry ice on receipt. If there is a temperature excursion over -40°F or if absence of dry ice, the material must be submitted to MRB for disposition.
3.02 Ship temperature controlled from 40°F to 65°F.
3.03 Ship at temperature controlled from 0°F and below (with evidence of Dry Ice).
3.04 Ship protected from ultraviolet light.
3.06 Ship at temperature controlled from 40°F to 90°F.
3.07 Resin content 37±3%. Flow 15±4%. Volatiles 2.5% Max.
3.08 Resin content 50±3%. Flow 15±4%. Volatiles 2.5% Max.
3.10 Specify Type, Grade and Class
3.11 Specify form (hand forging or die forging), alloy and temper
3.12 Safety walkway edge sealing compound must be purchased with Type IV.
3.13 Each batch of material shall be accompanied by a certificate of conformity.
3.14 Ship in heat sealed MIL-PRF-131 Class 1 Bags.
3.15 Material to have a high degree of tack to be compared to "Light Tack" quoted on Certificate of Test dated Jan. 18/93. (Batch 30089-00).
4.03 Whenever transparent film is required, acceptable substitutes are MIL-M-43719 or Commercial Plastics & Supply #CPA 500.
4.04 Density 11.13 to 12.67 lbs/ft³.
4.22 Flow 12 to 22% at 50psi 325°F 10 minutes: Gel time 60-110 seconds at 325°F.
4.24 Flow 10 to 24% at 50psi 325°F 10 minutes: Gel time 80-100 seconds at 325°F.
4.53 For nominal dimensions over one inch, procurement shall specify tolerances as called up on drawing
4.54 MIL-PRF-8184 Type 1 Class 2 can be substituted for MIL-PRF-8184 Type 1 Class 1.
4.57 Water absorption may be omitted from batch acceptance tests.
4.58 Material shall be supplied with a test report of radiographic inspection when required by the specification. Report shall contain the following information: (1) specific length of material purchased (2) specific length of material inspected (3) batch numbers from the manufacturer. Details and comments relative to the inspection should also be included. NOTE: The company issuing the C of C for the material is responsible for keeping the X-rays on file
4.60 Accelerated Weather Resistance testing as described in section 4.6.14 of MIL-W-5044 C for Type IV material may be waived as a batch release test by the manufacturer.
4.61 The outer surface of the wire or cable has to be markable with the Inkjet VEKTONICS wire vector 1100 system.
4.70 If fuel is supplied by CAFAS through Skyservices, then a laboratory report from CAFAS and a Certificate of Compliance from Skyservices are required. Both documents shall include traceability to the manufacturer of each original lot or batch.
4.71 If fuel is supplied by one of the approved manufacturers through Skyservices, then a laboratory report from the manufacturer and a Certificate of Compliance from Skyservices are required. Both documents shall include traceability to the manufacturer of each original lot or batch of material.
4.72 Bottles shall be labelled as: BAMS 565-007; MRV No. (From Bombardier Aerospace) Batch No. (From Supplier).
4.80 May be purchased to the requirements of MIL-S-8802 F Amendment 2.
4.81 None of the original shelf life of the material (calculated from the date of MANUFACTURE shall have passed upon receipt.
4.82 None of the original shelf life of the material (calculated from the date of SHIPMENT) shall have passed upon receipt.
4.83 No more than 1/4 (25%) of the original shelf life of the material (calculated from the date of manufacture) shall have passed upon receipt.
4.84 For components other than base and hardener/catalyst, such as solvents and activated solvents/thinners, it is permissible to purchase the component separately (outside of its respective kit). In such case, only a Certificate of Compliance from the supplier is required, and no test is required on receipt.
4.85 Sheets do not have to be identified using dye or ink per the Military Specification requirements. Each sheet must be identified using a label attached to it.
4.86 Use this material to depletion, but do not purchase any more. Refer to supersession list for replacement.
4.87 Material must be manufactured using pilot line 15 gallon mixers only.
4.90 Bottles shall be labeled as follows: DMS 2144 Comp. A, MRV No. (from Bombardier Aerospace), batch No. (from paint manufacturer)
4.91 Add separate test material requirements of Section 10.0, BAMS 532-019 specification to purchase order.
4.92 Add separate test material requirements of Section 10.0, BAMS 532-020 specification to purchase order.
4.93 PO to specify code (3) and abrasive not to contain metallic tin, lead or zinc. Total iron not to exceed .20%; only fused electric furnace aluminum oxide acceptable. Do not use reclaimed material .
4.94 520" long roll. Width 1/4" or 1/2".
4.95 Material to be tested in accordance with ASNB 71133 by the material manufacturer and results reported to BAMPE and Aerospatiale A/BTE/CD/MP R. Remark.
4.96 Material to be tested in accordance with ASNB 71134 by the material manufacturer and results reported to BAMPE and Aerospatiale A/BTE/CD/MP R. Remark.
4.97 AMS 3138-1 may be used in lieu of MIL-C-83231 Type I and AMS 3138-4 may be used in lieu of MIL-C-83231 Type II.
4.98 Material must conform to ASN-A-4165
4.99 Material must conform to ASN-A-4163
5.00 Material must conform to ASN-A-4172
5.01 If material is purchased from a vendor who is not the manufacturer, a Certificate of Compliance from the manufacturer is required for each batch or cylinder number.
5.02 If material is purchased directly from the manufacturer, a Certificate of Compliance and a test report from the manufacturer is required for each batch or cylinder number.
5.03 If material is purchased from a vendor who is not the manufacturer, a Certificate of Compliance and a test report from the manufacturer is required for each batch or cylinder number.
5.04 If material is purchased directly from the manufacturer, a Certificate of Compliance from the manufactutrer is required for each batch or cylinder number.
5.05 Material must conform to ASN-A-4168
5.06 Material shall come in as a kit, each component (base, hardener, thinner) shall be identified with the specification number under which it is being bought.
5.07 Thinner may be purchased separately with a "material not in EMCM form" in which case no test report is required, thinner must still be identified to ASN-B-70720-SP
5.08 Limited to the purchase of plastic balls
5.09 Unless otherwise noted, P.O. shall specify that sheets of material procured to this specification must be flat within +/- 0.050 inches under a 5 lbs per square foot loading
5.10 Ship refrigerated at 40°F or below for type III material
5.11 For Alcoa supplier, fluorescent penetrant inspection (FPI) per BAPS 176-002 shall be performed on 4" thick material and over. The inspection shall be performed by an approved source. A one-inch long sample shall be cut from the end of one plate per lot of material. The width of the sample shall be the total width of the plate. The interior surface of the sample shall be etched and FPI as required in BAPS 176-002. Failure to meet BAPS 176-002 requirements shall be cause for rejection.
5.12 Ship at temperature below 90°F. The shipment must be accompanied by a temperature indicator or a temperature recorder located at a top corner of the shipping container. If there is a temperature excursion above 90°F during shipment, the material must be submitted to MRB for disposition.
5.13 Manufacturer to test for crazing as per AS5127/1 at a stress of 3000 psi
5.14 If material is purchased from a vendor who is not the manufacturer, then a vendor's Certificate of Compliance is required for each lot or batch of material
5.15 Thinner may be purchased separately provided all other purchase conditions are met
5.16 All materials purchased to this specification shall be supplied with a total adhesive weight of 0.030 +/- 0.005 psf
5.17 It is acceptable to purchase this material per its commercial designation according to Le Joint Francais' standard (fiche controle quality). Material shall be tested per ASN-A-4168 on receipt
5.18 Material does not have to be bought as a system. Primer and topcoat may be purchased separately
5.19 Shelf life starts at date of manufacturing not receiving date
5.20 When indicated on Engineering Drawing, material 1/2 inch thick and greater shall be 100 percent ultrasonically inspected per BAC 5439 to the Discontinuity Class Requirement of the applicable material specification. For shapes, the thickness of any element of the shape shall be deemed to be the smallest dimension of that element.
5.21 If material is purchased directly from the manufacturer, a Certificate of Compliance and a Test Report from the manufacturer is required for each lot or batch of material. Certificate of Compliance does not have to state "We hereby certify that the material listed conforms with specification . . . ". The following wording is acceptable: "The accuracy or completeness thereof is not guaranteed."
5.22 If material is purchased directly from a vendor who is not the manufacturer, a Certificate of Compliance and a Test Report from the manufacturer is required for each lot or batch of material. Certificate of Compliance does not have to state "We hereby certify that the material listed conforms with specification . . . ". The following wording is acceptable: "The accuracy or completeness thereof is not guaranteed."
5.23 This material must use resin which complies with ASTM D4066 PA 630B00000.
5.24 Manufacturer shall perform on every batch flamability test per FAR 25.853, Appendix F, Part 1 (a)(1)(i)(vertical 60 sec.) and submit report.
5.25 MIL-P-38477 para 4.8.11.2; 4.8.11.3; 4.8.13 not required
5.26 Parts must conform to MPS 250-75
5.27 Stress corrosion test results per the requirements of the material specification
5.28 Flash point shall be 318 +/- 8°F.
5.29 Recrystallized Layer Thickness must conform to the maximum indicated on the engineering standard.
5.30 Manufacturer shall perform flamability test per FAR 25.853, Appendix F, Part I (a) (1) (ii) (vertical 12 sec.) on every batch and submit report.
5.31 Material must conform to ASN-B 71132-01
5.32 Ship at temperature controlled from 35 to 55°F.
5.33 Shipping requirements shall be as per the specification
5.36 Bottles shall be labeled as follows: BAMS 565-005, Type II; Batch no. (from Supplier)
5.37 Bottles shall be labeled as follows: MIL-PRF-22750; Batch No. (from supplier)
5.38 All materials purchased to this specification shall be supplied with a total adhesive weight of 0.045 +/- 0.010 psf
5.39 Suppliers of premix and frozen materials to this specification must comply with the "Suppliers Quality Assurance Provision for Premix and Frozen Material" section, as included in BAMS 552-009.
5.40 Primary colored stainers can be mixed to obtain the requested color match. Each batch of primary colored stainers shall meet all specification's requirements and be traceable to the batch number of the mixed product. Reports for each primary colored stainer shall be included with the mixed product report following purchase condition codes 2.01 & 2.02. Final mixed product shall be tested only for Weight per Gallon, Color and Gloss and these values shall be reported on a test report.
5.41 Material must conform to DHMS S3.01
5.42 Material must conform to ASTM D5363 AN0311
5.43 Compression deflection per ASTM D1056 (25%) must be maximum 2.5 psi
5.44 After reception of material, Receiving Quality shall re-identify as BAMS 532-040 Class I.
5.45 After reception of material, Receiving Quality shall re-identify as BAMS 532-040 Class II.
5.46 After reception of material, Receiving Quality shall re-identify as BAMS 532-040 Class III.
5.47 This product shall only be used for Learjet 45 Program.
5.48 Material must conform to AIMS 04-05-002 and IPS 04-05-002-09
5.49 Material must conform to IPS 10-07-001-01
5.50 Material shall be purchased from 3M / MTI-Polyfab Inc. (6300 Edwards Blvd, Missisauga, Ontario, CA, L5T 2V7 SAP 102074). 3M / MTI-Polyfab Inc. must perform receipt testing and provide a test report which includes results of the Radiant Panel Flame Propagation (FAR 25.856) and the peel tests per specification
5.51 If material is purchased dyed red, the dying procedure shall be per BAPS 140-013
5.52 All materials purchased to this specification shall be supplied with a total adhesive weight of 0.035 +/- 0.005 psf
5.53 The base and catalyst shall be procured and maintained at all times in the form of a kit consisting of each component in the proportions indicated in the Material Description
5.54 Material supplied shall be either 0.001" or 0.002" in thickness.
5.55 A Certificate of Compliance is required from the manufacturer with the date of fibre manufacture and application of size.
5.56 Material must conform to AIMS 03-05-016 and IPS 03-05-016-02
5.57 The material shall be kept at or below 80°F (27°C) during shipment, provided delivery takes a maximum of 7 days. A temperature recorder must be provided with each shipment.
5.58 The re-packaging company must provide Certificate of Compliance and Test Report from paint manufacturer as well as their own Certificate of Compliance to BAERD GEN-030, for each batch of material.
5.59 Material must conform to AIMS 04-05-001 and IPS 04-05-001-25
5.60 Shelf life extension on an unopened roll of material may be possible if the shipment includes an adhesive film sample (without the expanded metal foil) of 5 linear foot per batch of material, in addition of the sample required in BAMS 553-001 for acceptance testing. The sample shall be identified with the batch and roll number from which it was cut and then placed in MIL-PRF-131 Class 1 bag. The sample shall be stored with the batch of material it represents.
5.61 Mechanical properties (UTS, YS, %E) in the Longitudinal and Long Transverse direction shall be reported and shall meet latest MMPDS requirements for "L" and AMS Specification requirements for "LT" grain direction.
5.62 Material shall be rolled from slabs made from casting lines #19 & #20 only.
5.63 Hydrogen content "H2" of cast slab shall be reported and shall be .15 cm3 / 100gr of metals or lower.
5.64 Product tested by Bombardier to the requirements of BAMS 569-001. Purchase this product under its commercial name only.
5.65 Certificate of Compliance from the fiber manufacturer for each fiber batch employed within a subsequent braid or fabric lot to be supplied as a means of establishing product shelf life if this is not already identified on the final product Certificate of Compliance.
5.66 Certificate of Compliance from fabric manufacturer should state date of binder manufacture in order to establish bindered fabric shelf life.
5.67 Material 1/2 inch thick and greater shall be 100 percent ultrasonically inspected per AMS 2631 Class A1
5.68 Part must conform to BAPS 188-004
5.69 Product must be purchased packaged in multi-component cartridges only (Semkit, Techkit or equivalent).
5.70 Fuel shall contain anti-static additive meeting electrical conductivity requirements of material specification
5.71 A test report must be submitted for each truck load certifying it has been tested and meet specification requirements for undissolved water, sediment and suspended matter, density and electrical conductivity. In addition, the density must be compared to the manufacturer test report and shall not differ by more than 4 kg/cubic meter.
5.72 For round tube, the eddy current test shall be conducted in accordance with ASTM E 215. Each Length of tube, 1-1/2 inches or less in outside diameter and maximum wall thickness of 0.083 inch, shall produce eddy current indications less than those from the 2A holes of the applicable reference standard of ASTM E 215 or an equivalent secondary standard.
5.73 Approval of forgings is on a part-by-part basis. Refer to Table 14 (b) for approved part numbers. Hand forged billets/blocks without part numbers do not require approval on part-by-part basis.
5.74 For each lot, Bearing properties (Fbry, Fbru) with an e/D = 1.5 and e/D=2.0 in L-T direction shall be tested and reported and shall meet latest MMPDS requirements
5.75 Material shall be purchased certified to DHMS P1.48.
5.76 Test methods and requirements per DHMS P1.48.
5.77 Product was initially tested by Bombardier to the requirements of BAMS 516-007. Purchase product according to its commercial name only.
5.79 Material over 0.5 inch shall be 100 per cent ultrasonically inspected per AMS-STD-2154 Class A.
5.80 The material shall be shipped in a manner that assures transit and delivery at less than 10F (-12C). A continuous temperature recording device shall be included with each batch shipped.
5.81 Material shall have a maximum of 60 days of used storage life from the date of manufacture prior to shipment.
5.82 A Certifcate of Compliance to FAR Part 25, Paragraph 25.853, test methods as per Appendix F, Part I (a) (1) (ii) (vertical 12 sec.) with a coupon thickness of 0.25" +/- 0.01"
5.83 Manufacturer shall perform on every batch flammability test per FAR 25.853, test method and specimen configuration as per Appendix F, Part I (a) (1) (ii) (vertical 12 sec.) and submit report.
5.84 The manufacturer test report shall also include results for dry film properties of the batch acceptance tests of BAMS 565-015 applied over the specific batch of BAMS 565-008. Testing on Type I and Type II specimens of BAMS 565-015 may be omitted to certify the FR primer to BAMS 565-008.
5.85 The manufacturer shall perform all batch acceptance test specified in BAMS 532-040 Table 9. Requirements per BAMS 532-040 Class I, II or III, as applicable. The curing details and test methods shall be as defined in MAM-BA000-057. A test kit per BAMS 532-040 Section 11 shall also be supplied.
5.86 The manufacturer shall perform the following tests and issue a test report to the requirements of MAM-BA000-065 on each batch of sealant: application time, assembly time, standard curing rate and peel strength (7th set only).
5.87 Purchase order shall request conformance to L-P-410a and customer specification no. 22008. Customer specification no. 22008 includes a Bombardier approved sampling plan for lot acceptance testing.
5.88 The manufacturer shall perform all batch acceptance tests specified in BAMS 565-012 Table 5. Requirements per BAMS 565-012 Type II Grade 2.
5.89 Purchase order shall request conformance to L-P-410a and customer specification no. 22009. Customer specification no. 22009 includes a Bombardier approved sampling plan for lot acceptance testing.
5.90 Material must conform to DHMS P1.22 Type 1
5.91 A batch acceptance test report from the manufacturer is required for each lot or batch of material. Testing and requirements as specified in the Bombardier approved Process Control Document (PCD).
5.92 Manufacturer shall perform on every batch flammability test per FAR 25.856 and submit report
5.93 Each colour must initially be tested and provide 98% reflectance contrast ratio at 0.8 mils dry film thickness.
5.94 Precipitation hardened material may only be used when authorized by the Engineering Drawing. Material must be processed in accordance with and must meet the requirements of the specification AMS 5659/H1025.
5.95 Precipitation hardened material may only be used when authorized by the Engineering Drawing. Material must be processed in accordance with and must meet the requirements of the specification AMS 5629/H1000.
5.96 Each lot of material shall be tested for density and compressive strength.