1A2 Perform all the Quality Assurance / Batch or Lot Acceptance / Conformance / Initial Acceptance tests required of the manufacturer, as per the applicable section(s) of the material specification.

1A3 Flow and gel as per Test on Receipt Requirements

1A4 Tack

1A5 Peel

1A6 Shear as per Test on Receipt Requirements

1A7 Viscosity

1A8 Cure and tack free time as per Test on Receipt Requirements

1A9 Application time

1B1 Density

1B2 Hardness as per Test on Receipt Requirements

1B3 Expansion

1B4 Slump

1B5 Short beam shear

1B6 Flexural

1B7 Examine first 6 feet for tack and ease of unwind

1B8 Aerial weight

1B9 Compression

1C1 Flatwise tension

1C2 Prepreg resin content

1C3 Volatiles

1C4 Honeycomb node delamination

1C5 Crazing

1C6 Resistance to drying and ageing

1C7 Primer not cloudy or red

1C8 Extrudes freely, no lumps

1C9 Volume resistivity

1D1 Miscibility, pH

1D2 Specific gravity, water content, particle count, acid number, chlorine content

1D3 Condition in container, dry time, appearance

1D4 Dry time, appearance, gloss and color

1D5 Solids content

1D6 Penetrating properties

1D7 Corrosion resistance (salt spray)

1D8 Condition in container, gloss, adhesion

1D9 Conductivity per application specification

1E1 Fire resistance

1E2 Solvent resistance

1E3 Appearance

1E4 Test per MPS 202

1E5 Test per MPS 202-2

1E6 Sulphate concentration

1E7 Condition in container

1E8 Verify certificate of conformance

1E9 Test per MPS 202-1

1F1 Test per MPS 202-5

1F2 Test per MPS 202-4

1F3 Test per MPS 202-3

1F4 Color and gloss

1F5 Adhesion

1F6 Application life, dry time and curve time

1F7 Immersion and corrosion

1F8 Tensile strength and modulus

1F9 Flexibility and knife test

1G1 Test per MPS 202-14

1G2 Pot life, wet tape test

1G3 Pot life

1G4 Stability

1G5 Color, viscosity and application

1G6 Check for adequate propellant in aerosol container

1G7 Check that product is dry, powdery and contains no lumps

1G8 Check that, by spraying on a clean metal surface, product deposits evenly and smoothly

1G9 Test per MPS 212 Category 1

1H1 Test per MPS 212 Category 2

1H2 Test per MPS 212 Category 3

1H3 Test per MPS 212 Category 4

1H4 Test per MPS 212 Category 5

1H5 Test per MPS 212-4

1H6 Strength at Standard Conditions

1H7 Check for a good fluidity and homogeneity by visual inspection.

1H8 Test per ASTM D2095. Perform the test using one aluminum rod of any alloy. Requirement: 1000 psi minimum. BLS 9403 specimens are permitted.

1H9 Cured hardness of MIL-A-46106

1J1 Glass Transition Temperature

1J2 Flow/Slump/Slide

1J3 Consistency

1J4 Non-volatile content

1J5 Cure hardness

1J6 Compression strength plus modulus calculations

1J7 Compatibility with enamel

1J8 Sprayed appearance

1J9 Squeeze out life

1K1 Gel time

1K2 Resin content

1K3 Elongation

1K4 Corrosion inhibiting characteristics, drying time

1K5 CANCEL

1K6 CANCEL

1K7 Quality and appearance, viscosity, pot life, dry time metal anchorage, fluid resistant (water 140°F only)

1K8 CANCEL

1K9 CANCEL

1L1 CANCEL

1L3 Weight per gallon

1L4 Quantitator inhibitor analysis

1L5 Fluid resistance per specification

1L6 Melt flow index per ASTM D1238

1L7 Flammability per specification

1L8 Shrinkage

1L9 Flow

1M1 Flammability per specification

1M2 Cured ply thickness

1M3 Melt flow index per ASTM D1238

1M4 Shear Strength and modulus

1M5 Shear at 75°F ± 5°F

1M7 Lapshear A1/A1 Room Temperature, No Conditioning

1M8 Specific Gravity

1M9 Tensile strength

1N1 Test per MPS 138-45

1N5 Water Break

1N6 Appearance -Homogeneous and Fluid in the Can

1N7 Tack and Tack Free Time per MPS 157-30

1N8 Same as Test on Receipt

1N9 Tack Free Time 10 minutes at Room Temperature

1P1 Lapshear strength 2000 PSI at R.T.

1P2 Expansion

1P3 Flow Value at 20 ± 10%

1P4 Flow Value at 15 ± 5%

1P5 Flow Value of 10 ± 5%

1P6 Tack at 150 ± 10°F

1P7 Cure hardness of MIL-A-46146

1P8 Condition in container, Dust Free Time, Tack Free Time, Dry Through Time Application

1P9 Viscosity of Base and Catalyst

1R1 Pot Life per S26-1001

1R2 Test per CMS 532-20

1R3 Test per CMS 532-19

1R4 Gloss per Batch Acceptance Requirements

1R5 Drying Time per Batch Acceptance Requirements

1R6 Impact Resistance per Batch Acceptance Requirements

1R7 Fluid Resistance per Batch Acceptance Requirements

1R8 Viscosity to be 110 to 150 psi, use Bubble Viscometer from Gardrer.

1R9 FILM THICKNESS

1S1 Materials consisting of two or more components shall be shelf-life extended and maintained at all times in the form of the original procured kit.

1S2 Soft Gel Consistency

1S3 Standard Cure Time / Curing Rate

1S4 Peel per acceptance test

1S5 All acceptance tests per specification except for prepreg chemical properties

1S6 Tack Free Time

1S7 A uniform spray pattern with no leakage at the spray nozzle

1S8 Shall be easily mixed by stirring

1S9 Cured hardness per MIL-A-46146, Group I, Type I

1T1 All shelf life extension test per Material Specification

1T2 Rectify as per DMQR 1278

1T3 Test per MIL-C-38334, Type 1

1T4 Bond Shear Strength per Specification

1T5 Storage stability per paragraph 3.7.6 of MIL-T-9906 (Tensile, elongation and initial adhesion testing per ASTM D3330)

1T6 Total Acid Number

1T7 Work Life

1T8 Spraying Properties

1T9 Omit non-volatile content of the thinner

1U1 The curing agent shall be stirred before mixing with sealing compound to verify if it shows signs of settling or hardening. Faillure of the curing agent to return to a smooth, workable consistency shall be construed as a faillure.

1U3 Peel test per BATS 6304, set number 6, immersion (b). Requirement per material spec.

1U4 Peel test per BATS 6304, set number 6, immersion (d). Requirement per material specification.

1U5 Peel test per BATS 6304, set number 7, immersion (d). Requirement per material specification

1U6 Perform the Batch Acceptance Tests required of the manufacturer for Mixed Materials properties only, as per the material specification